Pages: 1 2Next >Last »

9″ Formflash

Description

Firestone 9″ formflash consists of a 229mm uncured Formflash, factory laminated to Quickseam Tape. The strip is designed to flash inside and outside corners, pipes, penetrations, drain outlets and any other awkward details.

Preparation

The EPDM surfaces and/or mating surfaces must be dry, clean, free from dust and be prepared with Firestone Quickprime Plus, using a quickscrubber pad. Use of other products is not allowed. Restore the product to room temperature prior to use if exposed to temperatures below 15 degrees for prolonged periods.

Application

On cloudy days with ambient temperature below 15 degrees, the use of a heat gun is recommended to warm the Formflash and to ensure good formability. On sunny days, pre-heating of the product is usually not necessary. Apply Firestone Quickprime Plus to all areas to receive the Formflash using a Quickscrubber pad and Handle. Allow the Quickprime Plus to completely dry before installing the Formflash, test for dryness by touching the Quickprime Plus with a clean dry finger. Remove the backing paper and carefully apply the Formflash to the pipe, corner, penetration etc. 

Physical Characteristics

  • Excellent moisture resistance
  • Excellent resistance to heat and cold
  • Excellent green tack

Quickprime Plus Must Be Used With This Product!

£13.32

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading

Contact Adhesive

Firestone Splice Adhesive is a contact adhesive, designed for splicing EPDM.

Preparation

Surfaces to be adhered must be cleaned with Firestone Splice Wash and allowed to dry. Stir the adhesive thoroughly before and during use, achieving a uniform mix with no sediment on the bottom and no marbling evident. Restore the adhesive to room temperature prior to use, if exposed to temperatures lower than 15 degrees for a prolonged period.

Application

Apply a thick, even, smooth coat on both surfaces using a 75 – 100mm wide solvent resistant paintbrush. Do not use circular motions for applying Splice Adhesive, do not use paint rollers or a brush attached to a long handle. Allow the adhesive to flash off prior to mating the surfaces (flash-off time depends on ambient air conditions). Test the adhesive for its dryness, using the push-touch procedure.

Coverage

A uniform application is required to avoid mixed results. Coverage rate for a standard splice width of 100mm, both sides is 30lm per 3.78 Litre tin.

Precautions

Flammable. Keep away from sources of ignition. Do not smoke when using. For professional use only. Use only in well ventilated areas. Avoid contact with skin and eyes. Keep out of the reach of children.


£35.00

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading

Edge Trim 3.5mtr

Available in Black or White

65mm Depth

Approx 30mm width on the edge 

 Designed with its own water-check kerb to be used around the perimeter of a flat roof to direct water towards the gutter edge.

Extruded using virgin plastic ensuring colour fast, non brittle, identical profiles. Manufactured BSI Quality assured  to 99.9% accuracy.

Permaroof Bond & Seal or Permaroof Closed Cell Foam Tape must be used to form a seal between the Trim and the EPDM.

Polypins are used to fix the trim into the Fascia Board.

Corner pieces and End caps are used to finish any open edges, these are injection moulded using state of the art manufacturing technology.

£12.00

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading

End caps

Edge Trim End Caps

Available in Black or White

These end caps are used for capping off the ends of the trim where they join each other or about an upstand.

Sold separately


£0.55

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading

External Corners

External Corner

90 Degree external corner

This is an Injection moulded corner piece available in Black or White, used on a 90 degree bend and also when an Edge Trim meets a Gutter Trim. It can be installed using Permaroof Bond & Seal or with Polypins, either way it provides a very neat, professional touch.


£1.40

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading

Firestone EPDM

Thickness 1.14mm

Features and benefits

Firestone E.P.D.M is a high performing synthetic rubber membrane offering a unique combination of features and benefits.

QUICK AND EASY INSTALLATION

Available in large sheet sizes anything up to 12.5m x 30m, resulting in fewer field seams and less installation time.

SUPERIOR WEATHERABILITY AND DURABILITY

Due to its composition, essentially EPDM polymers and carbon black, Firestone EPDM offers unmatched resistance to ozone, UV radiation, and ultimately ageing. Life expectancy of 50+ years!

HIGH FLEXIBILITY AND ELONGATION

Firestone EPDM remains flexible at temperatures down to -45 degrees and can elongate over 300% to accommodate building movements and temperature fluctuations.

LOW LIFE-CYCLE COST

Firestone EPDM requires little or no maintenance. This feature combined with the inherent durability and competitive installed cost of EPDM roofing systems, result in a very low life-cycle cost.

ENVIRONMENTALLY FRIENDLY

Firestone EPDM is an inert material with limited environmental impact during manufacture and use of the product.


£6.50

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading

Firestone waterbased adhesive

Firestone Water Based Adhesive

Description

Firestone Water Based Adhesive WBA-3781 is designed for bonding Firestone EPDM to Timber surfaces.

Preparation

Bonding surfaces must be clean, dry, smooth, free of sharp edges, loose and foreign materials, oil, grease and any other contaminants.

Application

Stir adhesive thoroughly before and during use. Use only when temperatures will not fall below freezing at anytime 24 hours after mating of EPDM.

Apply WBA-3781 over plywood or OSB substrates with a solvent resistant roller, taking care to completely cover the substrate evenly to avoid globs and puddles of adhesive. The EPDM may be Wet-mated to the coated plywood or OSB by rolling the membrane in place over the substrate. To ensure proper adhesion, compress the bonded portion of the sheet to the substrate with a stiff broom or heavy roller, such as a linoleum roller.

Coverage

Coverage Rate – Wet Applied to Timber Deck

2.5L Tub – approx 8 – 10m2

5L Tub – approx 18 – 20m2

10L Tub – approx 38 – 40m2

Storage

Store in original containers at temperatures between 15 – 25 degrees. Keep From Freezing

Shelf life – 18 months, when stored in above-mentioned conditions

Precautions

May cause mild transient eye irritation. Avoid contact with eyes, skin and clothing. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. If consumed, seek immediate medical attention. Keep container closed when not in use. Keep out of reach of children.

Firestone Water Based Adhesive Must Be Used Onto Timber

A Quick FAQ 

We often have customers ask what the difference is between Bonding adhesive and Waterbased / Deck Adhesive.  
 
Bonding adhesive is a much stronger adhesive which is used for bonding to most materials as well as wood and used around the edges of the EPDM, on any up-stands, bonding to brickwork etc where an effective and quick hold is required to keep the EPDM in place. Bonding adhesive is applied to both the EPDM and the surface.
 
Deck Adhesive / Waterbased Adhesive is more suited to wood and ply adhesion on the main area of the deck. The reasons why Waterbased / Deck is often used is because it is easy to lay, you can lay the EPDM straight onto it while it is still wet and it is also possible to correct mistakes shortly after the EPDM has been laid down up to 2-3 times if you find there is unwanted debris underneath due to it taking slightly longer than bonding to dry.  

£42.35

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading

Gutter trim 2.5mtr

Available in Black or White

Size 2.5m / Back Plate Dimensions – 75mm Depth, 20mm width (approx)

 A unique and patented design. Used along the Gutter edge. It sandwiches the EPDM roofing membrane eliminating penetration when fixing. It is a 2 part trim sold together and comes in 2.5m lengths.

APPLICATION

The Gutter back plate must be installed prior to the membrane, the top of the plate must be flush with the deck. The EPDM will overhang approx 50mm , the front plate is then pushed under the hook of the back plate with the membrane between the two, this will then clip into place to form a smooth finish.

Extruded using virgin plastic ensuring colour fast, non brittle, identical profiles. Manufactured BSI Quality assured  to 99.9% accuracy.


£12.00

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading

Internal Corners

Internal Corner

90 Degree Internal corner

This is an Injection moulded corner piece available in Black or White, used on a 90 degree Internal bend and also when an Edge Trim meets a Gutter Trim(as shown above). It can be installed using Permaroof Bond & Sealor with Polypins, either way it provides a very neat, professional touch.


£1.40

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading

Joint Clip

Joint Clip

Available in Black or White

40mm Width

This clip is used for joining two pieces of Permaroof Edge Trim together. It is moulded to the same shape as the Edge Trim and requires no fixings.


£1.20

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading

OSB 18mm Roofing Board (8 x 4)

Whether your building a new garage or extension, or whether its just in need of repairs you’re are likely going to need to replace the decking.

We take the hassle out of purchasing OSB SmartPly from your local merchants, we can have all of your flat roof materials including OSB delivered directly to your door.

OSB 3 SmartPly is the perfect substrate for EPDM applications as its hugely cost effective, eco friendly and is suitable for both structural and nonstructural applications.

HIGH QUALITY and environmental certification. Created from local sustainable forest resources in an energy efficient process.

Completely defect free – No knotholes or core voids.

Cuts easy and great to work with – A professionals choice.

£14.00

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading

Polypins

Stainless steal pins with plastic heads.

Used for securing the Permaroof edge trim to the fascia board

Available in Black

Size: 40mm

Box size: 250

£4.80

Please select product options before adding to cart

 

Item has been added to your cart!

 
Loading
Pages: 1 2Next >Last »